User's Manual Digital Display Alcohol Concentration Test Meter Model: AD-6000NS Precaution 1 ------------ Thank you for selecting and purchassing AD-6000NS Digital Display Alcohol Concentration Test Meter. Please read this manual carefully to ensure that you can use the product correctly. This device is a healthcare product; it is intended to control overdrink of alcohol so as to keep you fit, through testing the alcohol in your breath and calculating the content of alcohol via microcomputer. The product is applicable to family healthcare as well as for reference in determining whether the driver is driving after drinking. The test result may be affected by a number of aspects such as environmental temperature, various gases in the air and smoking, etc. the result shall, therefore, be only for reference and shall not be regarded as the justification of driving after drinking. No matter whether you have consumed this product, its manufactured and appropriate agents shall be not responsible for any traffic accident arisen due to ethanol or other accidents happened under therelated regulations and rules. As people's breath contains some fermentable gases (from stomach and intestines), so some gases may even be tested out under no drink circumstance. When after drinking, it is recommended to last after 20 minutes, it is because 20 minutes is approximately for alcohol to be absorbed into blood from the digestive organs, and residual alcohol remaining in the mouth takes this long to dissipate. For accurate result, do not repeat neat testing with in 3 minutes after time. Do not somke and eat for 20 minutes prior testing. Do not use any excitant substances near the tester, such as paing, insecticedes, alcohol. If the device has been performed for five times successively, please stop for two minutes and then use it again. Do not drive after drinking! Preparation Before Using 2 -------------------------- After opening the package, please check the parts and components below. If any one is absent, please contact its dealer. Accessories 1.One AD-6000NS LED digital display alcohol concentration detector 2.One User Manual 3.Three AA alkaline batteries. (not included) 4.6 air-blowing pipes. Battery Installation Install two 1.5V AA alkaline batteries with same specification into the battery case in a right way (as shown in figure 1) per the mark "+" and "-" on the case, and then close the cover well (as shown in figure 2) Battery Replacement If the yello LED on the LCDflashes, it indicates the battery electricity is not enough end the batteries need tobe replaced, in order to ensure the test accuracy. Open the attery cover end take out the batteries, and reinstall the new batteries with same specification (as shown in figure 3). Make sure to keep the old batteries out of children's reach, please dispose the useless batteries according to the local regulations. How to use the alcohol tester 3 ------------------------------- Operational Procedure: Wait Press the power button about 2 seconds, the alcohol tester LCD will tun on with one beep sound. The: "wark up" symbol is displayed and the 150 to 000 (or 15 to 00) countdown is stared that indicate the testeris in wark up mode. NOTE If first wark up is defeated, the tester will be reset automatically and wark up again for 1-3 times. It always has a large number of gaz & impurity adsorbed on the surface of alcohol sensor, when first time taking out the tester from the packaging, or after long time no using for the tester, it need more time for cleaning and wark up the alcohol sensor, you shouldrepress the power button and retry several times If possible. TEST The "BLO" symbolis displayed when wark-up is succeed, and the 100 to 000 countdown is stared that indicate the tester is in testing mode. Near and blow into the breath inhale for 3-5 seconds. Read the tester result from the alcohol tester lcd. Push the power button and hold 3s, the buzzer sound "B" one times, it is warming up and counting down from 150 about 15s. It will start to "BLOW" when it count down to "000" It will sounds and the grenn LED will light on and display "BLO" after counting down, it means you can start to test. "BLO" will shine about 10s. Confirm to blow within this 10s. Blow to the breath inlet about 5s, There is a long sound if there is alcohol, and it will display 003,002,001. After this, the result will show on. Only green LED shines and there are short sound "B,B,B" if the result is between 0.00-0.05. Only red LED shines and there are long sound "B,B,B" if the result is more than 0.05. The result will remain 15s, and then it will turn off. If there is no alcohol, it will display 0.00 after 10s shining "BLO". If will auto turn off if there is no alcohol or no testing within 30s after turning on. Auto power off 4 ---------------- 1. After the result be display for about 10 seconds, the "off" symbol will appear 2 seconds and the alcohol tester be turned off. 2. If wark up is defeated, the tester will automatically turned off. EOF